Posts Tagged With: maple

Kitchen Cabinets

I enjoy trying to organize each of these posts into logic pieces that show an entire step of the tiny house build. In the case of the kitchen cabinets I chose to post them all together rather than brake it up into individual components. This covers about three months of weekend working and many times we were working on multiple cabinets and shelves at once.

It all starts with the face frames constructed from the bi-pass door tracks.

SAM_0900

Dad cutting tracks for the bi-pass doors

The upper kitchen cabinet is assembled and clamped ready for the face frame.

IMG_1502

Upper kitchen cabinet clamped up

The completed upper cabinet features a built in knife rack.

IMG_1507

Upper kitchen cabinet completed

The lower pantry cabinet is assembled and awaiting bi pass doors and finishing.

IMG_1526

Pantry cabinet

The lower kitchen cabinet assembly. This will have a trash chute on the left side and sink in the middle.

IMG_1527

Lower kitchen cabinet assembly

SAM_0902

Lower kitchen cabinet process

We were able to construct this spice rack in a single day.

IMG_1467

Spice rack single day build

SAM_0847

Spice rack mounted

 

Kitchen cabinets in place.

IMG_1561

Kitchen cabinets in position

 

Categories: Tiny Home: Arborion | Tags: , , , , , | Leave a comment

Loft Storage

Much has happened since my last post. We have been busy finalizing designs and building the cabinets for Arborion. The first of these cabinets were ‘foot lockers’ for loft storage. I call them foot lockers because they are one foot high by one foot deep and used for storage. They also create a nice shelf just below the gable windows.

Foot locker frame and pieces

They are constructed from solid maple stock for the face frames and cleats, along with 1/2″ maple plywood. There is also a 1/2″ walnut plywood top on each.

Assembled and clamped up

There is a center partition for reinforcement which compliment a pair of bi-pass sliding doors.

Ready to transport and install

Storage loft locker

Sleeping loft locker

 

Categories: Tiny Home: Arborion | Tags: , , , , , , , , | Leave a comment

Lofts, Ceilings & Finish

The ridge of the 10′ ceiling is complete all the way into both lofts.

SAMSUNG CSC

Sleeping loft decking

SAMSUNG CSC

Back of Arborion

The lofts now have the bottom side covered with the 1/2″ maple plywood. This makes up the ceiling in the kitchen and bathroom as well as the reading nook (otherwise known as Carrie’s Corner) under the storage loft. The tops have been decked over with 5/8″ plywood on the sleeping loft and 1/2″ in the storage loft. The same bronze can lights are installed in the kitchen and bathroom ceilings as I used for the porch landing.

SAMSUNG CSC

Storage loft decking

SAMSUNG CSC

Front of Arborion

For the finish on the maple I used three coats of water-based matte polyurethane. The walnut was coated with a mixture of paraffin and linseed oil to match the door.

Categories: Tiny Home: Arborion | Tags: , , , , , , , | Leave a comment

Maple & Walnut Walls

For several weekends my Dad and I have been installing lightweight 1/2″ plywood as the finished walls inside the tiny house Arborion. Other than a few trim pieces, the walls are complete. Many of the pieces were fairly complex. They required careful measuring and several trips back to the work area under my carport to fine tune the shaping of each section. Like the ceiling, each section was installed one piece at a time with super construction adhesive and finish nails.

SAMSUNG CSC

My Dad applying construction adhesive before attaching the maple plywood panel

My brother, Daniel, was able to to help out during the first weekend of wall installation which was awesome. Having an extra set of hands and eyes on some of these large intricate sections was very helpful.

SAMSUNG CSC

Daniel and Dad working together on a complicated panel section

The walnut portion of the walls make up the lower 30 inches in a wainscot sort of appearance, while the maple fills the rest of the walls and ceiling. I am currently in the time consuming process of filling the small nail holes in preparation for the finishes I will be applying soon.

SAMSUNG CSC

Walnut panels in the bathroom

SAMSUNG CSC

Back of Arborion and bathroom

SAMSUNG CSC

Front of Arborion and reading nook

SAMSUNG CSC

Wall sections complete

Categories: Tiny Home: Arborion | Tags: , , , , , , , | 4 Comments

Maple-Paneling: Ceiling

I have been really excited to share this latest step in the tiny house build. Arborion has really taken on a beautiful look with its ceiling clad in light maple.

SAMSUNG CSC

First two panel pieces glued and finish nailed

I’m using half inch┬ámaple plywood with a garnica core that makes it very flat and light weight. The quality of the maple is such that the wood grain is very subtle, which is good since it covers such a large area. There is a warmth to the light that bounces down from the dormer windows off the angles of the maple ceiling.

SAMSUNG CSC

Sleeping loft complete except for a thin ridge panel

Fitting the panels to the angles and shapes of the ceiling and gables is a slow and painstaking task. By making cardboard templates of the trickier areas we saved making mistakes with our more expensive materials. We used construction adhesive and small finish nails in order to make a strong and permanent bond and keep a cleaner finished appearance.

SAMSUNG CSC

Main ceiling is coming along

On a separate note I must add that shaving down the closed-cell foam insulation is messy and time consuming work. The installers did wonderful work, but there are always areas that need more attention and trimming in order for the paneling to be installed properly.

SAMSUNG CSC

Storage loft looking good

Categories: Tiny Home: Arborion | Tags: , , , , , , | Leave a comment

Blog at WordPress.com.